首先，Ubuntu 10.10安装minicom：sudo apt-get install minicom
在安装好minicom之后对minicom进行配置，在此，需要注意的一点是在Linux环境下不许要装Usb转串口的驱动，在此，使用lsmod命令
linuxidc.com@ubuntu:~$ lsmod
Module Size Used by
pl2303 13696 0
usbserial 39507 1 pl2303
binfmt_misc 7984 1
可见，linux可以自动识别2303设备
之后在终端中输入dmesg | grep usb命令
linuxidc.com@ubuntu:~$ dmesg | grep usb
[ 0.497563] usbcore: registered new interface driver usbfs
[ 0.497574] usbcore: registered new interface driver hub
[ 0.497601] usbcore: registered new device driver usb
[ 1.001716] usb 2-3: new high speed USB device using ehci_hcd and address 2
[ 18.178144] input: USB 2.0 Camera as /devices/pci0000:00/0000:00:1d.7/usb2/2-3/2-3:1.0/input/input5
[ 18.178198] usbcore: registered new interface driver uvcvideo
[ 64.090038] usb 6-1: new full speed USB device using uhci_hcd and address 2
[ 64.328761] usbcore: registered new interface driver usbserial
[ 64.328807] usbcore: registered new interface driver usbserial_generic
[ 64.328810] usbserial: USB Serial Driver core
[ 64.362942] usb 6-1: pl2303 converter now attached to ttyUSB0
[ 64.362970] usbcore: registered new interface driver pl2303
注意上面加红的地方，他指明了设备号为：ttyUSB0
之后，就可以进行mimicom的配置了
在终端中输入：minicom -s,选择
+-----[configuration]------+
| Filenames and paths |
| File transfer protocols |
| Serial port setup |
| Modem and dialing |
| Screen and keyboard |
| Save setup as dfl |
| Save setup as.. |
| Exit |
| Exit from Minicom |
+--------------------------+
配置成如下方式：
+-----------------------------------------------------------------------+
| A - Serial Device : /dev/ttyUSB0 |
| B - Lockfile Location : /var/lock |
| C - Callin Program : |
| D - Callout Program : |
| E - Bps/Par/Bits : 115200 8N1 |
| F - Hardware Flow Control : No |
| G - Software Flow Control : No |
| |
| Change which setting? |
+--------------------------------------------------------------------
完成后退出，退出后进入 Modem and dialing 配置成如下方式：
（原因：我们使用的是串口，而不Modem）
+--------------------[Modem and dialing parameter setup]---------------------+
| |
| A - Init string ......... |
| B - Reset string ........ |
| C - Dialing prefix #1.... ATDT |
| D - Dialing suffix #1.... ^M |
| E - Dialing prefix #2.... ATDP |
| F - Dialing suffix #2.... ^M |
| G - Dialing prefix #3.... ATX1DT |
| H - Dialing suffix #3.... ;X4D^M |
| I - Connect string ...... CONNECT |
| J - No connect strings .. NO CARRIER BUSY |
| NO DIALTONE VOICE |
| K - Hang-up string ...... |
| L - Dial cancel string .. ^M |
| |
| M - Dial time ........... 45 Q - Auto bps detect ..... No |
| N - Delay before redial . 2 R - Modem has DCD line .. Yes |
| O - Number of tries ..... 10 S - Status line shows ... DTE speed |
| P - DTR drop time (0=no). 1 T - Multi-line untag .... No |
| |
| Change which setting? (Return or Esc to exit) |
+----------------------------------------------------------------------------+
配置完成后推出，在退出时一定要选择Save setup as dfl
到此，Minicom的配置完成，连上串口线，打开开发板电源即可看到串口输出的打印信息